The RTL8029AS controller is an NE2000 compatible Ethernet Controller for PCI interface. Taking the benefit of PCI's high throughput rate, the RTL8029AS controller offers a 32-bit data path to highly improve the data transfer rate compared with traditional Ethernet card on ISA, EISA and MCA bus. Due to the additional benefits of PCI, the RTL8029AS controller provides a low maintaining cost network environment without usage barriers. The Auto-configuration function of PCI can relieve the users from pains of taking care the system resource conflict. The RTL8029AS controller also supports full-duplex and power down features. With three levels power down control features, the RTL8029AS controller is made to be an ideal choice of the network device for a GREEN PCI PC system. The full-duplex function enables simultaneously transmission and reception on the twisted-pair link to a full-duplex Ethernet switching hub.
The Realtek RTL8221B(I)-CG is a highly integrated Ethernet PHY transceiver that is compatible with 10BASE-Te, 100BASE-TX, 1000BASE-T, and 2.5GBASE-T, and is fully compatible with both the IEEE 802.3 standard and the NBASE-T™ Alliance PHY. It provides all the necessary physical layer functions to transmit and receive Ethernet packets over CAT.5e UTP cable.
The RTL8218B-VC integrates quad independent 10/100/1000M Ethernet transceivers into a single IC, and performs all the physical layer (PHY) functions for 1000Base-T, 100Base-TX, and 10Base-T Ethernet on category 5 UTP cable except 1000Base-T half-duplex. 10Base-T functionality can also be achieved on standard category 3 or 4 cable.
Each of the four independent transceivers features an innovative QSGMII for reduced PCB traces. All transceivers can communicate with the MAC simultaneously through the QSGMII interface.
The RTL8218FB integrates octal independent Gigabit Ethernet transceivers into a single IC. The device performs all the physical layer (PHY) functions for 1000Base-T, 100Base-TX, and 10Base-T Ethernet on category 5 UTP cable except 1000Base-T half-duplex. 10Base-T functionality can also be achieved on standard category 3 or 4 cable.
The RTL8218FB Each of the two independent transceivers features an innovative RSGMII-Plus/QSGMII for reduced PCB traces. All transceivers can communicate with the MAC simultaneously through the same RSGMII-Plus/QSGMII.
The Realtek RTL8214QF is used to convert QSGMII Serdes interfaces to four 1000Base-X/100FX ports. IEEE802.3 Clause 22 MIIM formats are supported thus Switch controller can access the related register to get status and configure them.
The RTL8214C integrates quad independent 10/100/1000M Ethernet transceivers into a single IC, and performs all the physical layer (PHY) functions for 1000Base-T, 100Base-TX, and 10Base-T Ethernet on category 5 UTP cable except 1000Base-T half-duplex. 10Base-T functionality can also be achieved on standard category 3 or 4 cable.
Each of the four independent transceivers features an innovative QSGMII for reduced PCB traces. All transceivers can communicate with the MAC simultaneously through the QSGMII interface.
The RTL8214C integrates quad independent 10/100/1000M Ethernet transceivers into a single IC, and performs all the physical layer (PHY) functions for 1000Base-T, 100Base-TX, and 10Base-T Ethernet on category 5 UTP cable except 1000Base-T half-duplex. 10Base-T functionality can also be achieved on standard category 3 or 4 cable.
Each of the four independent transceivers features an innovative QSGMII for reduced PCB traces. All transceivers can communicate with the MAC simultaneously through the QSGMII interface
The Realtek RTL8211F-CG/RTL8211FI-CG is a highly integrated Ethernet transceiver that is compatible with 10Base-T, 100Base-TX, and 1000Base-T IEEE 802.3 standards. It provides all the necessary physical layer functions to transmit and receive Ethernet packets over CAT.5 UTP cable. The RTL8211FI-CG is manufactured to industrial grade standards.
The Realtek RTL8211FD-CG/RTL8211FDI-CG is a highly integrated Ethernet transceiver that is compatible with 10Base-T, 100Base-TX, and 1000Base-T IEEE 802.3 standards. It provides all the necessary physical layer functions to transmit and receive Ethernet packets over CAT.5 UTP cable. The RTL8211FDI-CG is manufactured to industrial grade standards.
The Realtek RTL8211FG-CG/RTL8211FG-VS-CG/RTL8211FGI-CG/RTL8211FGI-VS-CG is a highly integrated Ethernet transceiver that is compatible with 10Base-T, 100Base-TX, and 1000Base-T IEEE 802.3 standards. It provides all the necessary physical layer functions to transmit and receive Ethernet packets over CAT.5 UTP cable. The RTL8211FGI-CG and RTL8211FGI-VS-CG are manufactured to industrial grade standards.
The Realtek RTL8211FS-CG/RTL8211FS-VS-CG/RTL8211FSI-CG/RTL8211FSI-VS-CG is a highly integrated Ethernet transceiver that is compatible with 10Base-T, 100Base-TX, and 1000Base-T IEEE 802.3 standards. It provides all the necessary physical layer functions to transmit and receive Ethernet packets over CAT.5 UTP cable. The RTL8211FSI-CG and RTL8211FSI-VS-CG are manufactured to industrial grade standards.
The RTL8208D is a single-chip highly integrated 8-port, 10Base-T/100Base-TX Ethernet transceiver. Flexible hardware settings are provided to configure the
various operating modes of the chip. The RTL8208D provides an RS8MII interface-to-MAC controller for octal-PHY, allowing reduced IC pin count and PCB complexity.
The RTL8208L is a single-chip highly integrated 8-port, 10Base-T/100Base-TX Ethernet transceiver. Flexible hardware settings are provided to configure the
various operating modes of the chip. The RTL8208L provides an RS8MII interface-to-MAC controller for octal-PHY, allowing reduced IC pin count and PCB complexity
The RTL8201F-VB-CG implement all 10/100M Ethernet Physical-layer functions including the Physical Coding Sublayer (PCS), Physical Medium Attachment (PMA), Twisted Pair Physical Medium Dependent Sublayer (TP-PMD), 10Base-TX Encoder/Decoder, and Twisted-Pair Media Access Unit (TPMAU). The RTL8201F-VB-CG support auto MDIX.
A PECL (Pseudo Emitter Coupled Logic) interface is supported to connect with an external 100Base-FX fiber optical transceiver. The chip utilizes an advanced CMOS process to meet low voltage and low power requirements. With on-chip DSP (Digital Signal Processing) technology, the chip provides excellent performance under all operating conditions.
The RTL8201F-VD-CG implements all 10/100M Ethernet Physical-layer functions including the Physical Coding Sublayer (PCS), Physical Medium Attachment (PMA), Twisted Pair Physical Medium Dependent Sublayer (TP-PMD), 10Base-TX Encoder/Decoder, and Twisted-Pair Media Access Unit (TPMAU). The RTL8201F-VD-CG also supports auto MDIX.
A PECL (Pseudo Emitter Coupled Logic) interface is supported to connect with an external 100Base-FX fiber optical transceiver. The chip utilizes an advanced CMOS process to meet low voltage and low power requirements. With on-chip DSP (Digital Signal Processing) technology, the chip provides excellent performance under all operating conditions.
The RTL8201FI-VC-CG implements all 10/100M Ethernet Physical-layer functions including the Physical Coding Sublayer (PCS), Physical Medium Attachment (PMA), Twisted Pair Physical Medium Dependent Sublayer (TP-PMD), 10Base-TX Encoder/Decoder, and Twisted-Pair Media Access Unit (TPMAU). The RTL8201FI-VC-CG also supports auto MDIX.
A PECL (Pseudo Emitter Coupled Logic) interface is supported to connect with an external 100Base-FX fiber optical transceiver. The chip utilizes an advanced CMOS process to meet low voltage and low power requirements. With on-chip DSP (Digital Signal Processing) technology, the chip provides excellent performance under all operating conditions.
The RTL8201FR(I)-VD-CG is a single-chip/single-port 10/100Mbps Ethernet PHYceiver that supports RMII (Reduced Media Independent Interface).
The RTL8201FR(I)-VD-CG implements all 10/100M Ethernet Physical-layer functions including the Physical Coding Sublayer (PCS), Physical Medium Attachment (PMA), Twisted Pair Physical Medium Dependent Sublayer (TP-PMD), 10Base-TX Encoder/Decoder, and Twisted-Pair Media Access Unit (TPMAU). The RTL8201FR(I)-VD-CG also supports auto MDIX.
A PECL (Pseudo Emitter Coupled Logic) interface is supported to connect with an external 100Base-FX fiber optical transceiver. The chip utilizes an advanced CMOS process to meet low voltage and low power requirements. With on-chip DSP (Digital Signal Processing) technology, the chip provides excellent performance under all operating conditions.
The RTL8201FR-VB-CG is a single-chip/single-port 10/100Mbps Ethernet PHYceiver that supports RMII (Reduced Media Independent Interface).
The RTL8201FR-VB-CG implements all 10/100M Ethernet Physical-layer functions including the Physical Coding Sublayer (PCS), Physical Medium Attachment (PMA), Twisted Pair Physical Medium Dependent Sublayer (TP-PMD), 10Base-TX Encoder/Decoder, and Twisted-Pair Media Access Unit (TPMAU). The RTL8201FR-VB-CG also supports auto MDIX.
A PECL (Pseudo Emitter Coupled Logic) interface is supported to connect with an external 100Base-FX fiber optical transceiver. The chip utilizes an advanced CMOS process to meet low voltage and low power requirements. With on-chip DSP (Digital Signal Processing) technology, the chip provides excellent performance under all operating conditions.
The Realtek RTL8201G(I)-VB-CG (hereafter referred to as the RTL8201G(I)-VB-CG is a highly integrated Ethernet transceiver that is compatible with 10Base-T, and100Base-TX IEEE 802.3 standards. It provides all the necessary physical layer functions to transmit and receive Ethernet packets over CAT.5 UTP cable.
The RTL8201G(I)-VB-CG uses state-of-the-art DSP technology and an Analog Front End (AFE) to enable long-distance data transmission and reception over UTP cable with proprietary LD100 mode. For long-distance application over one-paired UTP cable or coaxial cable, 100BASE-T1 and another proprietary mode LD10 are implemented in the RTL8201G(I)-VB-CG to provide robust transmission and reception.
The Realtek RTL8201GR(I)-VB-CG (hereafter referred to as the RTL8201GR(I)-VB-CG is a highly integrated Ethernet transceiver that is compatible with 10Base-T, and100Base-TX IEEE 802.3 standards. It provides all the necessary physical layer functions to transmit and receive Ethernet packets over CAT.5 UTP cable.
The RTL8201GR(I)-VB-CG uses state-of-the-art DSP technology and an Analog Front End (AFE) to enable long-distance data transmission and reception over UTP cable with proprietary LD100 mode. For long-distance application over one-paired UTP cable or coaxial cable, 100BASE-T1 and another proprietary mode LD10 are implemented in the RTL8201GR(I)-VB-CG to provide robust transmission and reception.